The translation is temporarily closed for contributions due to maintenance, please come back later.

Source string Read only

(itstool) path: row/entry
Context English State
_ external ref='disklabel1' md5='__failed__'
If this is more or less what you need, it is very easy to adjust for journaling. Simply use the arrow keys to move the highlight to the <filename>/usr</filename> partition and press <keycap>D</keycap> to delete it.
Now, move the highlight to the disk name at the top of the screen and press <keycap>C</keycap> to create a new partition for <filename>/usr</filename>. This new partition should be smaller by 1 GB (if you intend to journal <filename>/usr</filename> only), or 2 GB (if you intend to journal both <filename>/usr</filename> and <filename>/var</filename>). From the pop-up that appears, opt to create a file system, and type <filename>/usr</filename> as the mount point.
Should you journal the <filename>/var</filename> partition? Normally, journaling makes sense on quite large partitions. You may decide not to journal <filename>/var</filename>, although doing so on a typical desktop will cause no harm. If the file system is lightly used (quite probable for a desktop) you may wish to allocate less disk space for its journal.
In our example, we journal both <filename>/usr</filename> and <filename>/var</filename>. You may of course adjust the procedure to your own needs.
To keep things as easy going as possible, we are going to use <application>sysinstall</application> to create the partitions required for journaling. However, during installation, <application>sysinstall</application> insists on asking a mount point for each partition you create. At this point, you do not have any mount points for the partitions that will hold the journals, and in reality you <emphasis>do not even need them</emphasis>. These are not partitions that we are ever going to mount somewhere.
To avoid these problems with <application>sysinstall</application>, we are going to create the journal partitions as swap space. Swap is never mounted, and <application>sysinstall</application> has no problem creating as many swap partitions as needed. After the first reboot, <filename>/etc/fstab</filename> will have to be edited, and the extra swap space entries removed.
To create the swap, again use the arrow keys to move the highlight to the top of <application>Disklabel</application> screen, so that the disk name itself is highlighted. Then press <keycap>N</keycap>, enter the desired size (<replaceable>1024M</replaceable>), and select <quote>swap space</quote> from the pop-up menu that appears. Repeat for every journal you wish to create. In our example, we create two partitions to provide for the journals of <filename>/usr</filename> and <filename>/var</filename>. The final result is shown in the following screenshot:
_ external ref='disklabel2' md5='__failed__'
When you have completed creating the partitions, we suggest you write down the partition names, and mount points, so you can easily refer to this information during the configuration phase. This will help alleviate mistakes that may damage your installation. The following table shows our notes for the sample configuration:
Partitions and Journals
Mount Point
Continue the installation as you would normally do. We would however suggest you postpone installation of third party software (packages) until you have completely setup journaling.
Booting for the first time
Your system will come up normally, but you will need to edit <filename>/etc/fstab</filename> and remove the extra swap partitions you created for the journals. Normally, the swap partition you will actually use is the one with the <quote>b</quote> suffix (i.e. ad0s1b in our example). Remove all other swap space entries and reboot so that FreeBSD will stop using them.
When the system comes up again, we will be ready to configure journaling.
Setting Up Journaling
Executing <command>gjournal</command>
Having prepared all the required partitions, it is quite easy to configure journaling. We will need to switch to single user mode, so login as <systemitem class="username">root</systemitem> and type:
<prompt>#</prompt> <userinput>shutdown now</userinput>
Press <keycap>Enter</keycap> to get the default shell. We will need to unmount the partitions that will be journaled, in our example <filename>/usr</filename> and <filename>/var</filename>:
<prompt>#</prompt> <userinput>umount /usr /var</userinput>
Load the module required for journaling:


No matching activity found.

Browse all component changes

Source information

Source string comment
(itstool) path: row/entry
Source string location
String age
a year ago
Source string age
a year ago
Translation file
articles/gjournal-desktop.pot, string 54